4.10 Release Notes

2012-05-14T15:06:54Z

Release 4.10.3 Changes:

← Older revision		Revision as of 15:06, 14 May 2012
Line 199:		Line 199:

	* bsp/genmcf548x: Fix configuration options and FPU initialization		* bsp/genmcf548x: Fix configuration options and FPU initialization
		+	* libblock: Critial fix for rtems_bdbuf_purge_dev()

	==Release 4.10.2 Changes==		==Release 4.10.2 Changes==

Makefile.am

2012-05-10T02:53:53Z

Closing out Conditionals):

← Older revision		Revision as of 02:53, 10 May 2012
Line 81:		Line 81:
	</pre>		</pre>

-	==== Closing out Conditionals) ====	+	==== Closing out Conditionals ====
	Although in the example, there are many calls to the conditional, using it once towards the beginning and end is okay.		Although in the example, there are many calls to the conditional, using it once towards the beginning and end is okay.
	<pre>		<pre>

Building the RTEMS toolset on Ubuntu

2012-05-10T02:52:40Z

Examples-v2:

← Older revision		Revision as of 02:52, 10 May 2012
(5 intermediate revisions not shown)
Line 120:		Line 120:
	See the [[Building Tools]] page for instructions on how to build from source. You may also try the [[RTEMS_Development_Hosts\|prebuilt tools]] route.		See the [[Building Tools]] page for instructions on how to build from source. You may also try the [[RTEMS_Development_Hosts\|prebuilt tools]] route.

-	== ~~Phase 3.~~ Build RTEMS ==	+	== Build RTEMS ==

	At this moment you can follow [[GSoC_Getting_Started#Configure_and_Build_RTEMS_for_SPARC.2FSIS]] and build RTEMS.		At this moment you can follow [[GSoC_Getting_Started#Configure_and_Build_RTEMS_for_SPARC.2FSIS]] and build RTEMS.
Line 145:		Line 145:
	Next follow the installation directions at http://www.rtems.org/wiki/index.php/Quick_Start		Next follow the installation directions at http://www.rtems.org/wiki/index.php/Quick_Start

-	== ~~Phase 4.~~ Build Qemu ==	+	== Build Qemu ==
	Install the dependencies:		Install the dependencies:

Line 210:		Line 210:
	</pre>		</pre>

-	== ~~Phase 4.~~ Build and Test Applications ==	+	== Build and Test Applications ==

	User supplied!		User supplied!
Line 216:		Line 216:
	http://www.rtems.org/wiki/index.php/Example_Application_Compiling		http://www.rtems.org/wiki/index.php/Example_Application_Compiling

-	... ~~Some additional applications are available at~~	+	=== Examples-v2 ===
-	~~I built example applications by~~	+	These are just some additional examples of how to get started with existing RTEMS applications.
		+	1. Use git to get the examples-v2
		+	2. Navigate to the examples-v2
		+	3. Tell Bash where to find the RTEMS_MAKEFILE_PATH
		+	4. Build the examples-v2 execuatbles
		+
	<pre>		<pre>
	$ git clone git://git.rtems.org/examples-v2.git examples-v2		$ git clone git://git.rtems.org/examples-v2.git examples-v2
Line 224:		Line 229:
	$ make		$ make
	</pre>		</pre>
-	~~Then I loaded both_hello~~ into ~~qemu by~~	+	Load the examples-v2 executables into Qemu's virtual filesystem.
	<pre>		<pre>
	$ qemu -m 128 -boot a -fda rtems-boot.img -hda hda.img -hdb \		$ qemu -m 128 -boot a -fda rtems-boot.img -hda hda.img -hdb \
Line 230:		Line 235:
	-serial stdio -no-reboot		-serial stdio -no-reboot
	</pre>		</pre>
-	~~Finally, I found~~ the executable~~, loaded it, and ran it~~.	+	-m 128: set the memory to 128
		+
		+	-boot a: boot from the a drive
		+
		+	-fda rtems-boot.img: load the rtems-boot.img into the a drive
		+
		+	-hda hda.img: use hda.img as the virtual hard-drive
		+
		+	-hdb fat:examples-v2/hello/both_hello/o-optimize/: use examples-v2/hello/both_hello/o-optimize as the root of the (FAT) virtual filesystem
		+
		+	To navigate while in grub:
		+
		+	1. find the executable in the virtual filesystem
		+
		+	2. set the root of the virtual filesystem as the root
		+
		+	3. load (multiboot) the executable
		+
		+	4. boot the executable
		+
	<pre>		<pre>
	grub> ls (hd1,1)/		grub> ls (hd1,1)/
Line 238:		Line 262:
	</pre>		</pre>

		+	=== Network Demos ===
	Now to try network-demos!		Now to try network-demos!
	<pre>		<pre>
Line 247:		Line 272:
	$ qemu -m 128 -boot a -fda rtems-boot.img -hda hda.img \		$ qemu -m 128 -boot a -fda rtems-boot.img -hda hda.img \
	-hdb fat:network-demos/http/o-optimize/ \		-hdb fat:network-demos/http/o-optimize/ \
-	-serial stdio -no-reboot	+	-serial stdio -no-reboot \
		+	-redir tcp:5555:80
	grub> ls (hd1,1)/		grub> ls (hd1,1)/
	grub> root=(hd1,1)		grub> root=(hd1,1)
Line 253:		Line 279:
	grub> boot		grub> boot
	</pre>		</pre>
		+	Without closing qemu, in Ubuntu, open Firefox, navigate to http://localhost:5555/

-	~~Addit~~	+	Additional applications can be found at: [http://git.rtems.org/[http://git.rtems.org/]]
-	[http://git.rtems.org/[http://git.rtems.org/]]	+	Information about these applications is provided at [http://wiki.rtems.org/wiki/index.php/RTEMS_GIT_Repository[http://wiki.rtems.org/wiki/index.php/RTEMS_GIT_Repository]]
-	Information about these applications is provided at	+
-	[http://wiki.rtems.org/wiki/index.php/RTEMS_GIT_Repository[http://wiki.rtems.org/wiki/index.php/RTEMS_GIT_Repository]]	+

RTEMSWiki - Recent changes [en]

4.10 Release Notes

Makefile.am

Building the RTEMS toolset on Ubuntu